Suzuki 2006 GSXR600/750 No Cut Frame Slider Install

2006 Suzuki GSXR600/750 Frame Sliders Install Instructions

Congratulations! You have just purchased the world’s finest frame sliders for the 2006 Suzuki GSXR600/750. These sliders have been designed to offer unsurpassed protection to your 2006 Suzuki GSXR600/750 in the unfortunate event of a lowside or tip over. Motovation frame sliders are designed and manufactured by a company that only makes frame sliders. Each and every model is tested for drop and slide protection. They are tough but not brittle and can also absorb a huge impact. Sportsriders around the world who have tested various models of our products on the track have all given their thumbs up after experiencing first hand, the benefits of Motovation Frame Sliders.

Please read all instructions before beginning work! These frame sliders are designed to fit specific engine mounts of your 2006 Suzuki GSXR600/750. This kit has separate left and right pieces (left and right while sitting on the bike). It is highly recommended that you refer to your service manual before performing this installation. If you are unsure about the tightening torque, check your motorcycle's manual or www.motovationusa.com/torque.html for a quick reference guide.

Included in the Street kit: (1) M10x 120 mm 1.25 pitch heat treated 12.9 grade socket head bolt (left side w/longer slider) (1) M10x 90 mm 1.25 pitch heat treated 12.9 grade socket head bolt (right side w/shorter slider) (2) M10 Stainless Steel Washers (2) Anodized Aluminum bushings (pressed into plastic) (2) Frame Sliders
INSTRUCTIONS:
	Left Side (while sitting on bike) Before beginning make sure your left side fairing is removed. 1. Remove the left-side engine mount bolt (forward lower mount). 2. Install the left(longer) slider bolt without the slider. Engage only a few threads and re-install the fairing to mark the inside of the fairing for the pilot hole. We sometimes coat the head of the socket screw with a non permanent marker or place some putty on the inside of the fairing so the the screw will make a mark or an indentation. Once the center of the bolt location on the fairing is determined, it is suggested that you drill a small pilot hole to locate the engine mount. Once you have found the center, use a hole saw and cut a hole approximately 28 mm in diameter. Edges can be filed for perfect fit, or inaccuracies in drilling. We have found that placing masking tape on the area helps protect from scratches, cracks, etc. 3). Reinstall your fairings. 4). Install the left slider (longer) using the M10 x 120mm bolt and washer supplied in this kit. Use of some Locktite is recommended. 5). Tighten the slider bolt to the approximately 39 ft/lbs - DO NOT OVERTIGHTEN.
	Right Side (while sitting on bike) 1. Remove the right-side engine mount bolt (forward lower mount). 2. Install the shorter slider with the M10x 90mm bolt and supplied washer. 3. Tighten the engine mount bolt to the factory specifications - DO NOT OVERTIGHTEN. A bit of Locktite on the bolt threads is recommended.

Thank-you for purchasing Motovation products. Please ride safe and always wear protective clothing.

WARRANTY AND LIABILITY LIMITATIONS
Except as may be expressly set forth in the product invoice, MotovationUSA makes no representations or warranties as to any of the products distributed by us, expressed or implied, including without limitation any warranties of merchantability or fitness for a particular purpose. Motorcycles can be dangerous. MotovationUSA has no control over the usage of any part and expects their customers to exercise good judgment as to the proper selection, installation, use and maintenance of any part. MotovationUSA assumes no responsibility for damage or injury of any kind because of the misuse or improper application of any part in any way by any person. MotovationUSA shall not be liable for any indirect or consequential damages whatsoever. All matters shall be interpreted under Texas law. All merchandise distributed by MotovationUSA is guaranteed against defects in material and workmanship only. Final decision will be made in a just and prompt manner. Replacement will be limited to parts only and does not include labor claims of any type. If the manufacturer has a written warranty, it will be included with the item you purchased. The manufacturer shall be solely responsible for any damage to person or property arising from design and manufacture and testing of its products and we accept no liability for such damages. We shall not be liable for consequential damages.