REVISED 2007 Yamaha YZF1000 R1 Race (no cut) Frame Sliders Install Instructions

Congratulations! You have just purchased the world’s finest frame sliders for the 2007 Yamaha R1. These sliders have been designed to offer unsurpassed protection to your Yamaha YZF1000 R1 in the unfortunate event of a lowside or tip over. Motovation frame sliders are designed and manufactured by a company that only makes frame sliders.

Please read all instructions before beginning work! These frame sliders are designed to fit specific engine mounts of your Yamaha R1. This kit has separate left and right pieces (left and right while sitting on the bike). It is highly recommended that you refer to your service manual before performing this installation. If you are unsure about the tightening torque, check your motorcycle's manual or www.motovationusa.com/torque.html for a quick reference guide.

Important: Ensure the the bike is on a rear stand and is level to avoid engine shifting during engine bolt removal. Only attempt installation of this kit one side at a time. Blocking of the engine from below is advisable.

Included in this kit:

Left Bracket (smaller)
1xM10x60mm, 1xM8x45mm and 1xM6x45mm
1 aluminum spacer
80mm flat side slider w/stainless screw

Right Bracket (larger)
1x M10x65mm, 1xM6x65mm and 1xM6x35mm
70mm flat side slider w/stainless steel screws.

INSTRUCTIONS: 		 

Yamaha 2007 R1 frame sliders

Left Hand Side ( Sitting On Bike )
Remove the top and bottom fairing by removing the 2 quick release M6 screws. Remove the M10 engine bolt. Use the supplied M10 screw to attach the bracket.Install the aluminum thin spacer provided to the M10 bolt to at the back of the bracket between the frame and bracket. Do not tighten yet.
Remove the corresponding M6 and M8 stock case bolts and attach the bracket to them with the supplied M6 and M8 bolts. Do not tighten yet.
Once the bracket is place and screws are hand tight and correctly seated, then slowly tighten each bolt sequentially until snug.
Now install the longer slider onto the bracket.
Lastly re-install fairings.
Important: Do not exceed the manufacturer’s recommended torque settings. Some Loctite blue is highly recommended on all installed bolts
DO NOT OVERTIGHTEN.

Right Hand Side (sitting on bike)
Remove the top and bottom fairing by removing 2 quick release M6
Remove the M10 engine bolt. Slide the larger bracket underneath the hose and bolt the first M10 screw, do not tighten yet.
Remove the 2 M6 case screws(1 long and 1 short) and install the bracket with the two supplied M6 Screws
Once the bracket is place and screws are hand tight and correctly seated, then slowly tighten each bolt sequentially until snug.
Now install the shorter slider onto the bracket.
Lastly re-install fairings.
Important: Do not exceed the manufacturer’s recommended torque settings. Some Loctite blue is highly recommended on all installed bolts
DO NOT OVERTIGHTEN.

Thank-you for purchasing Motovation products.  Please ride safe and always wear protective clothing.

WARRANTY AND LIABILITY LIMITATIONS
Except as may be expressly set forth in the product invoice, MotovationUSA makes no representations or warranties as to any of the products distributed by us, expressed or implied, including without limitation any warranties of merchantability or fitness for a particular purpose. Motorcycles can be dangerous. MotovationUSA has no control over the usage of any part and expects their customers to exercise good judgment as to the proper selection, installation, use and maintenance of any part. MotovationUSA assumes no responsibility for damage or injury of any kind because of the misuse or improper application of any part in any way by any person. MotovationUSA shall not be liable for any indirect or consequential damages whatsoever. All matters shall be interpreted under Texas law. All merchandise distributed by MotovationUSA is guaranteed against defects in material and workmanship only. Final decision will be made in a just and prompt manner. Replacement will be limited to parts only and does not include labor claims of any type. If the manufacturer has a written warranty, it will be included with the item you purchased. The manufacturer shall be solely responsible for any damage to person or property arising from design and manufacture and testing of its products and we accept no liability for such damages. We shall not be liable for consequential damages. © 2007 Motovation Accessories