Motovation Honda CBR1000RR Installation Guide - Frame Sliders and Accessories

Motovation Honda CBR1000RR Street Model Frame Sliders Install Instructions(Improved)

Congratulations! You have just purchased the world’s finest frame sliders for the Honda CBR1000RR. These sliders have been designed to offer unsurpassed protection to your Honda CBR1000RR in the unfortunate event of a lowside or tip over. Motovation frame sliders are designed and manufactured by a company that only makes frame sliders. Each and every model is tested for drop and slide protection. They are tough but not brittle and can also absorb a huge impact. Sportsriders around the world who have tested various models of our products on the track have all given their thumbs up after experiencing first hand, the benefits of Motovation Frame Sliders.

Please read all instructions before beginning work! These frame sliders are designed to fit specific engine mounts of your Honda CBR1000RR. This kit has separate left and right pieces (left and right while sitting on the bike). It is highly recommended that you refer to your service manual before performing this installation. If you are unsure about the tightening torque, check your motorcycle's manual or www.motovationusa.com/torque.html for a quick reference guide.

Included in this kit: (2) frame sliders w/aluminum inserts. (2) M10x40 1.5 SS bolts and washers (for slider to bracket installations) (2) anodized aluminum brackets (four hole bracket-left side) (2) small anodized aluminum spacers (for lower left side) (1) larger aluminum spacer (for upper left side) (2) M6x55mm SS bolts(left side bracket) (1) M12x80 1.25 bolt (left side) (1) M12x90 1.25 bolt (right side) (2) 6mm Standoffs (shorter for the left)
INSTRUCTIONS:
	Important! Remove bolts one side at a time. Perform this installation on a cool engine. Left Hand Side (Sitting On Bike) Remove fairing panels Remove correct engine bolts. Insert bolts and spacers into bracket as shown Install the bracket into the frame as shown and tighten the 3 bolts to manufacturer's specs. Install the slider to the bracket with the M10x40mm SS bolt and washer. Tighten to the manufacturer’s recommended torque settings. DO NOT OVERTIGHTEN. Locktite is strongly recommended.
	Right Hand Side (Sitting On Bike) Remove (See picture) correct engine bolt. Install the provided bracket to the frame with the supplied 90mm bolt as shown. Tighten to manufacturer's specs. Install the slider to the bracket with the M10x40mm SS bolt and washer. Tighten to the manufacturer’s recommended torque settings. DO NOT OVERTIGHTEN. Locktite is strongly recommended. Install the two standoffs onto the rear fariing stays(shorter on left) Hand tighten with a bit of locktite. Replace fairing panels and secure the rear part of the fairing with the supplied pan head screws onto the standoffs.

Thank-you for purchasing Motovation products. Please ride safe and always wear protective clothing.

WARRANTY AND LIABILITY LIMITATIONS
Except as may be expressly set forth in the product invoice, MotovationUSA makes no representations or warranties as to any of the products distributed by us, expressed or implied, including without limitation any warranties of merchantability or fitness for a particular purpose. Motorcycles can be dangerous. MotovationUSA has no control over the usage of any part and expects their customers to exercise good judgment as to the proper selection, installation, use and maintenance of any part. MotovationUSA assumes no responsibility for damage or injury of any kind because of the misuse or improper application of any part in any way by any person. MotovationUSA shall not be liable for any indirect or consequential damages whatsoever. All matters shall be interpreted under Texas law. All merchandise distributed by MotovationUSA is guaranteed against defects in material and workmanship only. Final decision will be made in a just and prompt manner. Replacement will be limited to parts only and does not include labor claims of any type. If the manufacturer has a written warranty, it will be included with the item you purchased. The manufacturer shall be solely responsible for any damage to person or property arising from design and manufacture and testing of its products and we accept no liability for such damages. We shall not be liable for consequential damages.